CABLOFIL CABLE TRAY-WHITE (6D,,8W,,120L) [944849]
CF150/200WH
Cablofil
Bazaarvoice SAP Hybris Integration Version 2.8.1
Cablofil Wiremesh Cable Tray concept based upon performance, safety and economy
- Send
- Save as PDF
-
Added to Favorites Go to favoritesRemove from favorites?Something went wrong. Please try again later.
Features
- Special Safe-T-Edge: protects installers from sharp ends while it prevents cables from fraying.
- Wire mesh is smooth and round: to resist dirt and dust build-up.
- Standard 10' lengths: straight and easy to handle.
- Large mesh size (2'' wide by 4'' long ): allows cable installers to route cables in and out at any point without cutting the tray.
- 1'' to 6'' high flange side of the tray: prevents cables from falling off.
- Dimensions are nominal: other sizes available on request.
- Available in the following finishes: Electro Zinc, Hot Dipped Galvanized, Stainless Steel 316L, Black Painted, and other Painted.
- View our Technical Guide here.
Specifications
General Info
Product Line | Cablofil | ||
Finish | Painted | ||
UPC Number | 800388249042 | ||
Country Of Origin | United States | ||
Application Sector | Commercial, Industrial | ||
Type | Straight Sections |
Dimensions
Product Width US | 7.87 in | ||
Product Weight US | 20.13 lb | ||
Product Volume US | 3.515 cu ft | ||
Product Depth US | 118.2 in | ||
Product Height US | 6.53 in |
Buy American Act Compliance
BAA | Yes |
Resources
Cutsheet
Installation Instructions
Guide Form Specifications
Reviews
Bazaarvoice SAP Hybris Integration Version 2.8.1
Questions & Answers
I need to order the CF105 Basket Tray. Unfortunately I can not find any part numbers so I can order the tray. I have a very large order to submit and Your assistance would be greatly appreciate.
At the bottom of the webpage there is a CF105 cut sheet that includes the available widths. I've also attached a catalog snapshot.
Date published: 2024-08-05
The max. wire diameter is listed as 5.9mm. What is the minimum wire diameter?
As the original inventor and world’s largest manufacturer of welded wire mesh cable tray, Cablofil cable tray products have many unique and patented features. Through our research and design efforts, we have discovered that certain wires in the cable tray are load bearing and other wires are not load bearing. Our cable tray design has increased the diameters of the load bearing wires 25% greater than 0.196” and the non-loadbearing wires at or slightly below 0.196”. This unique combination of wire sizes, patented in the United States and around the world, allows Cablofil cable trays to be stronger than the competitors that must use all 4mm diameter wires to achieve comparable load capacity. Cablofil cable trays also deflect less when loaded and are faster to cut since only the load bearing wires are larger. I recommend using load tables to compare strength of trays as cable diameter does not correlate to a stronger product.
Date published: 2024-01-05
where do i find accessories for CAB 901 CF105/150EZ
There are many accessories compatible with CF105/150EZ. I recommend downloading the Cablofil catalog. This is the easiest way to review Cablofil's wire mesh cable tray options.
https://www.legrand.us/resources/catalog?q=%3Arelevance%3AlrProductLine%3ACablofil&text=#mca
Date published: 2023-11-10
Should 18" wide tray be supported on each side of tray if suspended from ceiling?
Typical ceiling-hung wire mesh installations include an AS trapeze hanging clip on each side rail, a FASP trapeze hanger or a FASPCH center hanger.
Date published: 2024-03-28
Hi, I am in search for Marine certificate, does Cablofile has some of marine certificate? Thanks
Please reach out to technical.support-CAB@legrand.us. They can email Cablofil's ABS Certificate to you
Date published: 2023-10-03
Do you provide the CF105 electroplated zinc custom painted (specifically red)?
Cablofil's standard practice is to powder coat over bare steel which provides the best adhesion. Replace the suffix EZ in your part number with PE. Let your sales rep or distributor know that PE = red.
Date published: 2024-03-28
How do I bend a horizontal offset
Wire mesh fittings are field fabricated so there are multiple ways to make fittings. If you are trying to make a 90 degree horizontal elbow you could use the EZT90EZ bend kit. I recommend downloading Cablofil's catalog from the website. There is a 24-page section detailing how to make different kinds of bends.
Date published: 2023-02-16
What is the requirement specifications for Seismic Support placement and frequency of placement?
In geographic regions of moderate seismic activity, a good starting point is a 4-way sway support such as the SZMCKIT or similar every 30’ and at the support nearest to each fitting. Seismic calculations can be quite rigorous in high active areas. If a detailed analysis or drawings are required, the contractor should hire an engineering firm to review and make recommendations.
Date published: 2022-12-28
Are wire mesh type cable trays available in aluminum?
Wire mesh cable tray products are only available in steel or stainless steel. Cablofil invented wire mesh cable tray in 1972 and is the world’s largest producer. We can assure you that aluminum wire mesh tray is not available in the United States or anywhere in the world.
The resistance welding process used to make wire mesh tray produces a strong welded gridwork of wires required to make a robust cable tray. Resistance welded aluminum is not common in manufacturing for any industry due to the weak weld strength and weld strength inconsistency. Aluminum ladder tray is welded utilizing a different welding process (typically MIG or TIG) which is not conducive to use with wire rods.
We assume at some point in time the specification was changed from an aluminum ladder tray to a wire mesh tray but the material change was missed.
Date published: 2022-12-13
Can CF150/600EZ be stored outside?
The electro-zinc (EZ) finish is used in dry, indoor installations. EZ cable tray should be stored in a well-ventilated, dry location. It should not be stored outdoors.
Date published: 2022-12-13
I am looking for a snap on J-Hook for a CABLOFIL CABLE TRAY-BLACK (4D,12W,120L) [941118). I will need a large amount so if you could please provide model #, specifications and price will be great.
Cablofil sells J-hooks with a snap-on bracket that allows them to be mounted to wire mesh tray. Please see the attached catalog snapshot.
Cablofil sells through distribution. There is a Where to Buy link in the upper right hand corner of www.legrand.us that can be used to find your local sales rep or distributor.
Date published: 2023-10-09
Are there any grounding requirements for cable tray? If so, Can you send me info? Thank you!
I have attached a copy of our bonding/grounding brochure.
Date published: 2023-11-09
I am running CF150 cable tray and the inspector is requesting information on the clips that join 2 piece of the cable together. Does this provide continuity for grounding or is a grounding jumper required between the 2 pieces.
EDRNEZ and SWKEZ are UL classified splices. No bonding jumper is required.
Date published: 2023-02-17
What is the maximum load capacity of CF105 / 600EZ? What is the maximum load capacity of CF105 / 300EZ?
The wire mesh cable tray load table can be found on catalog page A.6
Date published: 2023-02-02
where do i find accessories for CF105/150
Bazaarvoice SAP Hybris Integration Version 2.8.1