LS Series Dual Fan Speed Control|Dimmer, White

In my wall/fan I have Black -hot/motor Red - light White - neutral Green - ground So then... Outlet. Fan. Black & red. - Black/motor Yellow. - Red/light Green. - Green White to white.

This device needs to be on the LINE(hot) side of your 3way with power going to the Black wire and it will provide power to both fan and light control. The two Yellow wires would connect to your traveler wires for your 3way light and one Red wire would be connected to your fan(one Red is capped off). Pass & Seymour products 1.800.223-4185 opt 1 Mon - Fri: 8am - 8pm EST (excluding holidays) Email Us - tech.support@legrand.us

The dimmer portion of the dual controller is not rated to handle a motor load(fan) so it will not work to control two fans.

For installation assistance please contact technical Support directly: Pass & Seymour products 1.800.223-4185 opt 1 Mon - Fri: 8am - 8pm EST (excluding holidays) Email Us - tech.support@legrand.us

You need at least three wires(1 HOT & 2 LOAD wires), plus ground for this dual controller to be able to turn your light and fan on separately.

I would suggest contacting Technical Support to go over the correct wiring for this dual controller. Your load wires(fan & light) need to be separated and your light wire goes to the yellow wire and your fan wire goes to the red wire(non-flagged wires). Pass & Seymour products 1.800.223-4185 opt 1 Mon - Fri: 8am - 8pm EST (excluding holidays) Email Us - tech.support@legrand.us

Yes this switch will work. It can be wired for single pole or three way circuits. The diagrams in the instructions will demonstrate how. This switch is rated for incandescent bulbs.

You may want to double check Your wiring to make sure everything is tight and secure. I would reccommend calling into our tech support team at 1800 223 4185 opt 1 for additional support

The LS series control is compatible with three way wiring applications. The directions that come with the device include a wiring diagram to illustrate an example of three way wiring.

The fan side of this device is not rated to control any type of light load so it will not dim properly.

The dimmer can only be wired per the instructions included with the device. You could wire it up to a fan and light itself or in unison with a three way switch.

We do not offer a device that can dim 2 separate LED lights from one unit.

Thank you for your question regarding the LS Series Preset 3-speed/3way De-Hummer Fan Control with 3way Dimmer(Model # LSDC163PLAV). This dimmer is designed for use with Incandescent bulbs only. We do have the LSCLDC163PLA that is designed for select dimmable CFL/LED or incandescent lighting loads. https://www.legrand.us/passandseymour/fan-controls/de-hummer/ls-series/lscldc163pla.aspx

Thank you for your question regarding LS Series Dual Fan Speed Control/Dimmer, White (LSDC163PWV). When using this device to control both the light and fan in a 3way application, you would need a 3way switch for the light and a 3way switch for the fan on the other end of the circuit.

Thank you for your question regarding Pass & Seymour Dual Dimmer & Fan control. This device is designed to control the light and fan separately so your HOT wire would to the black wire, your light wire would go to the yellow wire, and your fan wire would go to the red wire for a single pole application. You will have a red and yellow wire that will get capped off(only used in a 3way). Pass & Seymour products 1.800.223-4162 opt 3 Mon - Fri: 8am - 8pm EST (excluding holidays)

For Trouble shooting support feel free to contact tech support at 1800 223 4185 Option 1 If the product is defective We can send a replacement for You

Thank you for your inquiry regarding our LSDC163 Dimmer and fan speed control combination device. Please contact us at 800-223-4185 regarding the wiring of this product. We will need to discuss the wiring set up you have and what the trouble is here. Hope this helps!