CordMate II Kit - White

Hello, Yes, the adhesive can be removed without damaging the wall. One method is to use vinegar in a spray bottle. Spray the vinegar on the adhesive and let it sit for a period of time and then carefully remove the adhesive with a putty knife. Thanks,

Hello Flippo, The Cordmate II system is not compatible with the Cordmate I and vice versa. Unfortunately there are no adapters to go from one system to the other.

Hello, The Cordmate II system is equal to our 2800-WH series on the commercial division. Here is a link to the product spec sheet will all available parts, unfortunately there are no 45° angles available and it would be best to make that connection on site using a miter saw. These can be ordered through a local distributor in your area is the local retailers cannot access them. All of the parts on the spec sheet that being with "28" are compatible with the 2800/CordMate II system. https://legrand.webdamdb.com/directdownload.php?ti=55654545&tok=NtS7RomkuRIlmrK2hmuWzwRR If you need help with where to purchase locally you can do the following: Click this link for "where to buy" - https://www.legrand.us/where-to-buy Select "shop local or find a sales rep" Under "Where to buy" select "distributor" Under "brand name" select "Wiremold" Lastly, input your zip code and hit search. The list of distributors will populate below the map.

The channel included with the C210 is sold through electrical distributors in 6' lengths under p/n 2800-WH. It's sold in standard packages of 120'.

Hello Bob, Thank you for your inquiry. An end cap is available for this product. Our part# is 2810B-WH and listed below is a link to the product page for this piece. https://www.legrand.us/wire-and-cable-management/raceway-and-cord-covers/nonmetallic/uniduct-2800-series-blank-end-fitting-fitting/p/2810b-wh?text=2810B-WH Feel free to reach back out to us direct with any additional questions. Our number direct is 1-844-957-3783. From the main menu choose option 2 for Wiremold followed by 2 for Technical Support. Take care and thank you for choosing Wiremold products.

Good Afternoon- The Uniduct Nonmetallic Latching Raceway System (Cordmate ll) is a one-piece, single channel design, ideally suited to route and protect fiber optic, UTP, and other low-voltage (50V or less) cables.

Hello, The Cordmate system is only available in a white finish. We do offer it in a ivory finish on the commercial side as part number 2800. Since the product is PVC is can easily be painted to match the surface. It would be suggested to prime and paint using a latex based paint. For assistance with the commercial part numbers please contact the factory directly at 1-800-621-0049 option 3.

Yes, the they can. Flat elbow part number is 2811-WH.

Yes, our Cordmate II can be painted using latex paint.

Hello, the C210 is only available in the kit. For parts outside of the kit and pricing please contact our customer support team directly at 1-800-621-0049, or email customer.support-wm@legrand.us for assistance.

Hello, Yes, this is made of PVC.

Hello, The best suggestion would be to squeeze the the end of the track. Once you compress it the cover will allow you to "peel" it open. Once you get the end started just slide your finger the rest of the way to release the rest of the cover.

The adhesive provided on the Cordmate as well as our other Raceways strongly bonds to the wall. This is very desirable for most applications. However, in some cases it probably isn't because if you try to remove the Cordmate from the wall after it sticks it is likely to cause some damage. It will leave behind a residue which will be difficult to clean and could pull some of the surface off of the drywall with it as it comes off. The following methods can be used to remove the product and adhesive from the wall; 1) Using a spray bottle, spray vinegar directly where the adhesive is adhered to the wall. Let the vinegar soak in to the adhesive for a period of time. The vinegar will help deteriorate the adhesive. A putty knife can be used to pry the product/adhesive away from the wall surface. 2) Use a citrus based adhesive remover from a local hardware store. Follow the instructions on the bottle.

The channel is capable of holding a max of two cat 6 size cables, roughly .25" - .27" dia. I would measure, or look up the specs the cables you're using and see if they are close to that.

The adhesive tape on that raceway is intended for mounting to clean, dry, grease-free, smooth surfaces. The texture of Stucco wall will most likely not allow it to adhere properly.