text.skipToContent text.skipToNavigation

Power Pack, 120-277V, 50/60Hz, 24VDC, 225mA,

The BZ-200 power pack switches connected loads On and Off in response to Wattstopper low voltage occupancy sensors. It also provides up to 225mA at 24VDC to power the sensors. This device is constructed with environmentally friendly materials and is RoHS-compliant.

Send
Save as PDF
Added to Favorites Go to favorites

Remove from favorites?

Something went wrong. Please try again later.

Features

Efficient switching power supply provides optimized current output based on number of sensors
Includes short circuit and thermal protection
LED indicates status of relay or presence of low-voltage overcurrent
UL 2043 plenum rated for cost-effective installation
UL listed for control of lighting and plug loads
Tested to NEMA 410 criteria for electronic ballast and driver inrush current
1/2”” threaded nipple attaches to standard electrical enclosures through 1/2”” knockouts

Specifications

General Info

Color	White
Product Series	BZ
Type	Power Pack
Material	Plastic
Application Sector	Commercial
Product Line	Wattstopper
Country Of Origin	China
Installation Location	Ceiling
Warranty Type	5-Year
UPC Number	754182938032

Dimensions

Product Depth US	1.4 in
Product Height US	3.0 in
Product Volume US	42.0 cu in
Product Width US	3.0 in
Product Weight US	0.4 lb

Additional Information

RoHS Compliant

Yes

This product meets the material restrictions of Article 4 of the RoHS Directive (2011/65/EU), including Commission Delegated Directive 2015/863.

Technical Information

Wire Connection Type	Wire Leads
Connection Type	Wired
Indoor/Outdoor	Indoor
Input Voltage	120 to 277 VAC
Line Frequency	50 Hz, 60 Hz
Mounting Type	1/2 in Knockout
Operating Temperature	-4°-131°F
Operating Temperature Max	131 °F
Operating Temperature Min	-4 °F
Operating Humidity	5-95% RH (Non-Condensing)
Output Voltage	24 VDC
Storage Temperature	-40° - 176° F
Wire Gauge	18-22 AWG

Resources

Can I used it with Single Pole Momentary Switch,  to controlle the load OFF?

Asked by: Ia

The answer to your question would be yes it can be used with a single pole momentary switch.

Answered by: Tier 1 Tech Support

Date published: 2023-07-17

Can the power pack turn the load off when the room is occupied? Load off when occupied 

Asked by: Dean

More information is needed to properly address your request. Please contact Wattstopper Technical Support @ 800-879-8585 for further assistance.

Answered by: Tier 1 Tech Support

Date published: 2022-04-13

Can A BZ-200 be used with a dimmer switch?

Asked by: Duane Ogletree

Yes, a BZ-200 can be used with a DCLV2 dimming switch.

Answered by: Tier 1 Tech Support

Date published: 2022-04-13

Can a BZ-200 be used for receptacle control?

Asked by: shooter

Yes the BZ-200 can be used for receptacle control. The Cutsheet for the BZ-200 specifically discusses it's use for plug load control.

Answered by: Tier 1 Tech Support

Date published: 2021-08-03

Recently Viewed

Weatherproof Two Gang Box, Gray

WPB232 | Pass and Seymour

View Details

2X4 Cablofil Center Hanger-Pregalv (4D,,2W,,4L) [586100]

SF100PG | Cablofil

For center hanging 4 inch wide wire mesh tray Fold over tabs secure tray without additional hardware Pre Galvanized finish for indoor use

View Details

1-Gang Pre-configured Wall Plate with One RJ11 Telephone Jack, White

TPTE1W |

1-Gang Pre-configured Wall Plate with One RJ11 Telephone Jack

$3.67

View Details

Non-Fusible Safety Switch with 3 Auxiliary Contacts, 30A

PS30SSAX3 | Pass and Seymour

Non-Fusible Safety Switch with 3 Auxiliary Contacts, 30Amps, 600 VAC.P&S Non-Fusible Safety Switches feature extra-tough components, including an impact-resistant Valox NEMA 4X enclosure. And an innovative design that delivers safe, sure operation under the worst conditions.

View Details