Trademaster® Wide Slide Single-Pole/3-Way, Preset CFL/LED Dimmer, White
WSCL453PW
Pass and Seymour
Bazaarvoice SAP Hybris Integration Version 2.8.1
Works with select dimmable CFL/LED or incandescent lighting loads and features a sleek, sculpted ergonomic design for smooth, easy operation and precise control.
Application Sector
Residential/Commercial
- Send
- Save as PDF
-
FavoriteAdded to Favorites Go to favoritesRemove from favorites?
Features
- Convenient Operation - Combines ON/OFF Decorator style switch with separate slider for dimming control.
- Constant memory returns lights to previous level after a power failure.
- Sleek, ergonomic design that matches well with other decorator products.
- Higher ratings.
- Single pole and 3-way operation.
- Screw-pressure-plate back wire terminals to save time, space and money.
- Rating: 450W LED & CFL: 700W Incandescent: 120VAC 60Hz.
Specifications
General Info
| Product Line | Pass & Seymour | ||
| UPC Number | 785007039375 | ||
| Country Of Origin | China | ||
| Application Sector | Residential/Commercial | ||
| Standard | cULus, RoHS |
Technical Information
| Wattage | 450 W | ||
| Voltage | 120 V |
Resources
Cutsheet
Brochure
Supporting Document
CAD Drawings
Installation Instructions
Guide Form Specifications
Reviews
Bazaarvoice SAP Hybris Integration Version 2.8.1
Questions & Answers
Is there a list of compatible LED bulbs for this dimmer? I have been unable to find any, but the instructions say you can find a list at www.legrand.us
You can reach out to Technical Support and they can provide you with a list of compatible LED bulbs:
Pass & Seymour products
1.800.223-4185 opt 1
Mon - Fri: 8am - 6pm EST
(excluding holidays)
Email Us - tech.support@legrand.us
Date published: 2021-02-19
Confused by wiring instructions for single pole, which usually use brass colored screws with black screw being “common” for 3-way but this model has one of the brass screws taped off and the tape and instructions both say only use that screw for common?
The wiring for a single pole application would be as follows:
Hot wire to Black terminal(#1 on diagram) and Load wire to brass terminal(no tape - # 3 on diagram)
Date published: 2019-10-07
Is this an ELV dimmer? Are all of your CFL/LED dimmers at this rating level, even if in different operational styles, also ELV? Same question for the dual fan control, motor load on one side for fan and ELV dimmer for LED light on fan?
This dimmer is not rated for ELV. This dimmer is intended for CFL and LED bulbs that screw into a medium base socket. We do not offer an ELV dimmer in this series. We do offer our Tru Universal dimmer Model RH703PTU for ELV loads. I have attached the link
https://www.legrand.us/search.aspx?q=rh703ptu
Date published: 2018-08-27
What is the procedure for adjusting dimmer when brightness varies at times ?
The procedure to adjust the dimmer is as follows:
Dimmer may require adjustment to the low end setting to reliably start and/or
remove flickering in bulbs. To adjust, DISCONNECT POWER FROM CIRCUIT, and
remove the Wallplate. Use a small insulated, flat tipped screwdriver to adjust the
trim pot wheel, which is accessible via the slot (marked “CALIBRATION”) provided
on the strap (Figure 1). Turn the wheel downwards to increase the minimum light
intensity setting and turn the wheel upwards to decrease light intensity. Next,
install the Wallplate, restore the power and test. Repeat above as necessary.
If that doesn't correct the light levels, I would verify that you have the correct dimmer for your type of lighting. The WSCL453 dimmer is designed for Incandescent/CFL/LED medium base bulbs only.
Date published: 2018-08-12