Wiremold CordMate Cord Cover Kit is the quick, easy way to conceal a single cord or cable. Its stylish design complements most interior decors and is great for concealing lamp and extension cords as well as phone cables. The kit comes 9 ft. of channel and multiple fittings so you have everything you need to complete an average project in your home or office.
- Send
- Save as PDF
-
Added to Favorites Go to favoritesRemove from favorites?Something went wrong. Please try again later.
Features
- Streamlined: to blend with any décor.
- Great for Concealing and Cord Organizing: conceal phone wires, cables, cords and speaker cable.
- Self-adhesive backing: simple to install on a baseboard or wall.
- Perfect for family rooms or bedrooms.
- Easily organize cords and cables.
- Paintable.
- This product meets the material restrictions of RoHS.Tools needed for installation:
- Tape measure
- Fine tooth hacksaw
Specifications
General Info
Product Line | Wiremold | ||
UPC Number | 086698880292 | ||
Country Of Origin | United States | ||
Application Sector | Residential | ||
Standard | Raceway is not NRTL Listed and is only designed for use in protecting electrical cords and low voltage wiring and cabling. | ||
Type | Raceway |
Additional Information
RoHS Compliant | Yes | This product meets the material restrictions of Article 4 of the RoHS Directive (2011/65/EU), including Commission Delegated Directive 2015/863. |
Buy American Act Compliance
NAFTA | Yes |
Resources
Cutsheet
Instruction Sheet
Brochure
Customer CAD PDF
Reviews
Bazaarvoice SAP Hybris Integration Version 2.8.1
Questions & Answers
What is the best way to adhere corner pieces to Cordmate tubes?
Hi,
Those are designed to snap over the raceway channel.
Thanks,
Date published: 2024-03-28
Do they make a "T" connector?
Hello Bobby,
A tee connector is not available for this series.
Date published: 2024-06-18
Is there an end cap available to cover an exposed end?
Hello,
Unfortunately, we do not offer an end cap for the C110 as the intended use is for the end to remain open for cord pass-through.
Thank you,
Date published: 2024-01-29
What is the best solution, please, when the adhesive backing of the pieces that hold the cord no longer sticks to the wall?
Hello,
The adhesive can be replaced with a multi-surface double-sided tape. However, all adhesive has a shelf life and mechanical fasteners are recommended for a permanent installation.
Thank you,
Date published: 2023-01-26
Are these products available in a brown color? Also, are they rated for outdoor use?
Hi Matt,
The C110 is available in white through retail purchase or ivory through the commercial distribution. These products are for interior dry locations only, not suitable for outdoor use. Unfortunately there are no raceways/cord covers available for outdoors.
Date published: 2022-08-25
Do you offer items C16, C17, C18 and C19 separately? I especially need a C18 elbow to reinstall a Cordmate after replacing an electric cord.
Cordmate part numbers C16, C17, C18 and C19 can be purchased separately. Those are the actual numbers you need to use to order them. They are sold through the same vendors and stores that the Cordmate kit is sold by.
Date published: 2022-08-17
C110 work? Single cable ( USB A to mini-B 5pin 28/28AWG) run down side of 7' window & across bottom window frame to recharge unreachable motor shade battery. Indoors but will get sun/cold exposure. Can C110 be screwed to wood?
Yes, the C110 can be used for a single cord or cable in an indoor dry location. The channel is only 1/2" wide, but wood screws can be used to fasten the channel to the frame.
Thank you
Date published: 2022-03-08
What is the best way to open the raceway after it’s been installed to replace cable on the C110 size?
Hello,
The best suggestion is to use a small flat head screw driver at the end of the section to pry the cover open. Once you get the end unlatched you can begin to pull the cable out down the length of the track which should release the cover. Otherwise you may need to run the screw driver down the length of the track. You should be able to twist the screw driver once you get it crease where the cover meets the base, if not then you may need a second screw driver or something behind to help with leverage. Once you get it started at one end the rest will release
Date published: 2022-01-06
Bazaarvoice SAP Hybris Integration Version 2.8.1