text.skipToContent text.skipToNavigation

Wide Slide TradeMaster Single-Pole/3-Way, Preset CFL/LED Slide Dimmer, 3 Interchangeable Face Plates

  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 257ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

Works with select dimmable CFL/LED or incandescent lighting loads and features a sleek, sculpted ergonomic design for smooth, easy operation and precise control.
Color White
WHERE TO BUY

Features

  • Convenient Operation - Combines ON/OFF Decorator style switch with separate slider for dimming control.
  • Constant memory returns lights to previous level after a power failure.
  • Sleek, ergonomic design that matches well with other decorator products.
  • Higher ratings.
  • Single pole and 3-way operation.
  • Screw-pressure-plate back wire terminals to save time, space and money.
  • Rating: 450W LED & CFL: 700W Incandescent: 120VAC 60Hz.

Specifications

General Info
Color White, Light Almond, Ivory
UPC Number 785007039535
Country Of Origin China
Product Line Pass & Seymour
Application Sector Residential/Commercial
Standard cULus, RoHS
Technical Information
Wattage 450 W
Number of Poles Single Pole
Voltage 120 V
Connection Screw Terminals
Frequency Rating 120VAC 60Hz Hz
Load CFL/LED
Environmental Conditions Humidity: Less than 95% non condensing

Reviews

  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 75ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

Questions & Answers

Installed this summer in three rooms. I get an occasional flickering of the lights in all three rooms. is this switch more comparable with certain bulbs or what else could be causing this flicker?

Asked by: Cg123
The WSCL453 dimmer has a calibration wheel to adjust for flickering on some CFL/LED bulbs: #8 from instruction sheet: Dimmer may require adjustment to the low end setting to reliably start and/or remove flickering in bulbs. To adjust, DISCONNECT POWER FROM CIRCUIT, and remove the Wallplate. Use a small insulated, flat tipped screwdriver to adjust the trim pot wheel, which is accessible via the slot (marked “CALIBRATION”) provided on the strap (Figure 1). Turn the wheel downwards to increase the minimum light intensity setting and turn the wheel upwards to decrease light intensity. Next, install the Wallplate, restore the power and test. Repeat above as necessary. Note: Never adjust trim pot when circuit is live. To re-calibrate settings turn the trim pot wheel all the way up towards the “-” sign and incrementally progress to “+” sign until flickering is removed (refer to Step 8 above).
Answered by: Legrand Technical Support
Date published: 2020-11-21

Can I get a replacement face plate (white) for this switch (WSCL453PTC )?

Asked by: Doug
Thank you for your inquiry. Please contact our technical support team at tech.support@legrand.us or by phone at 1-800-223-4185.
Answered by: Legrand Technical Support
Date published: 2020-11-20

I have this dimmer on a 3 way location but i also need a companion or controller switch, is there a compatible switch available?

Asked by: Charlie
You can only dim from one location in your 3way with this dimmer so any 3way switch will work, like our TM873W(if using white).
Answered by: Legrand Technical Support
Date published: 2020-09-21

how long do these last? I have used one for about 2-3 months, and its already failed. Won't turn on no matter the setting. I replaced the swtich with a standard switch, an no issues with the circuits. I have this attached to 6 dimmable LED blubs.

Asked by: nickD
The dimmer is expected to last for years and is covered by a Lifetime Warranty, should it fail.
Answered by: Legrand Technical Support
Date published: 2020-07-21

Looking to use with total of 6 bulbs, dimmable 6w GE LED6DASW9C-LT8. Is this switch compatible... will it dim all the way to zero and will there be no buzzing? Have had difficulty with other LED dimmers, want to make sure this one works

Asked by: Sasha
The WSCL453PTC should handle 6 bulbs(36W total) with no issues and it has a calibration wheel to adjust the Low End Trim level. Dimming down to zero may also depend on the LED bulbs dimming restrictions. Some LED's only dim to 5 or 10%.
Answered by: Legrand Technical Support
Date published: 2020-06-08

Is there a minimum load requirement for this dimmer?

Asked by: Matt
A minimum load of 10W is recommended for optimal operation of the dimmer.
Answered by: Legrand Technical Support
Date published: 2019-07-31

The on-off switch works but the dimmer slide has no effect. Lights will not dim. Only on or off. What's wrong?

Asked by: Grumpy
If you are dimming CFL or LED bulbs with this dimmer, you need to verify that they state the are "dimmable". Pass & Seymour products 1.800.223-4185 opt 1 Mon - Fri: 8am - 8pm EST (excluding holidays) Email Us - tech.support@legrand.us
Answered by: Legrand Technical Support
Date published: 2021-04-17

Installed dimmer which seemed easy enough.  Connected both common to common terminal and both black to other terminal.  Light will not shut off or dim.  

Asked by: Tom25
For a single pole installation, your HOT wire would go to the Common(black) terminal and LOAD wire(from your light) would go to 1pole terminal. If you have white neutral wires, they would get wire nutted together and not attached to the dimmer. Pass & Seymour products 1.800.223-4185 opt 1 Mon - Fri: 8am - 8pm EST (excluding holidays) Email Us - tech.support@legrand.us
Answered by: Legrand Technical Support
Date published: 2019-05-13
  • y_2021, m_10, d_21, h_18CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.19
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_11
  • loc_en_US, sid_WSCL453PTC, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_legrand
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 194ms
  • QUESTIONS, PRODUCT