


High/Low PIR Integrated Outdoor Fixture Mount Sensor
FSP-211-CFG
Wattstopper
Bazaarvoice SAP Hybris Integration Version 2.8.1
The FSP-201 mounts in an outdoor lighting fixture and provides multi-level control based on motion and/or daylight contribution. It controls 0-10 VDC dim-to-off LED drivers or ballasts, or works with a power pack to control other loads. When used with an FSP-Lx Lens, the sensor is rated for wet and cold locations. All control parameters are adjustable via a wireless configuration tool capable of storing and transmitting sensor profiles.
Voltage
None
- 12 V
- 120/277 VAC
- 347 VAC
- None
- Send
- Save as PDF
-
Added to Favorites Go to favoritesRemove from favorites?Something went wrong. Please try again later.
Features
- Fully adjustable high and low dimmed light levels; optional dusk to dawn control
- Controls 0-10V dim-to-off LED drivers or ballasts, or works with a power pack to control other loads
- Hold off setpoint with automatic calibration option for convenience and added energy savings
- Adjustable via handheld wireless configuration tool
- IP66 rated with choice of lenses for wet and outdoor locations, and mounting heights from 8’ to 40’
- Adjustable time delay and cut off delay
Specifications
General Info
Product Line | Wattstopper | ||
UPC Number | 754182940981 | ||
Country Of Origin | China |
Additional Information
Product Environmental Profile | Yes |
Technical Information
Sensor Type | Occupancy, Daylight |
Resources
Product Environmental Profile
Installation Instructions
Instruction Sheet
Reviews
Bazaarvoice SAP Hybris Integration Version 2.8.1
Questions & Answers
Can the FSP-211 be programed, disconnected from power, and maintain settings? We are wondering if we can pre-configure before sending to the job.
Hi Allan,
Yes, you can pre-program the sensors before sending them to site and they will retain the settings.
Date published: 2023-08-09
Is the FSP-211 interchangeable with a failed FSP-201 in my Big As garage light? TIA
Hi Jim,
No, the FSP-201 is low voltage and the FSP-211 is line voltage. We recommend swapping it out for the same existing FSP-201 sensor model.
Date published: 2023-08-09
Will the The FSIR-100 handheld remote tool interface with this unit?
Hi,
Yes,this sensor can only be adjusted using the FSIR-100 remote.
Date published: 2023-03-27
Can I use one FSP-211 for several (3 pcs) LED luminaires (dimming 1-10V)? Can I connect FSP-211 with driver only with 3 wires (GRND, DIM+, DIM-), wires L and N to go directly to driver, not over FSP-211?
Good evening
If you still need any help from Wattstopper support please contact us at 1-800-879-8585 option #1.
Date published: 2022-06-21
Is it possible to get a 3-D cad model of the FSP-221
The nature of this request is best addressed by an application specialist, we cannot post CAD files in this forum. Please contact Wattstopper Technical Support @800-879-8585 so that your request can be directed through the proper channels.
Date published: 2022-06-13
IS it possible to have a 3D model or DXF drawing of the FSP-201? Thanks for the support
Below is a CAD drawing for the FSP 201 to give you some answers to your question.
Date published: 2022-05-23
What is the default position for the FSP-211, if it were to fail at EOL? Would the light default on or off?
Whether it fails in the ON or OFF state depends entirely upon the mode of failure, so we cannot state that it will always fail in a particular state.
Date published: 2022-11-11
Will these work if mounted behind clear plastic?
Bazaarvoice SAP Hybris Integration Version 2.8.1