text.skipToContent text.skipToNavigation

angled image of Power Pack, 120-277V, 50/60Hz, 24VDC, 225mA

Power Pack, 120-277V, 50/60Hz, 24VDC, 225mA, Wire Connector

The BZ-50 Universal Voltage Power Pack provides 24 VDC operating voltage to Wattstopper’s low-voltage occupancy sensors. This device is constructed with environmentally friendly materials and is RoHS-compliant.

Connection Type Wire Leads

RJ45
Wire Leads

Send
Save as PDF
Added to Favorites Go to favorites

Remove from favorites?

Something went wrong. Please try again later.

Features

Self-contained power supply relay system
Efficient switching power supply providing optimized current output based on number of sensors
LED indicates status of relay or if there is a low-voltage overcurrent
The product meets the materials restrictions of RoHS
Zero crossing circuitry for reliability and increased product life
UL 2043 plenum rated for cost-effective installation
1/2”” snap-in nipple attaches to standard electrical enclosures through 1/2”” knockouts

Specifications

General Info

Application Sector	Commercial
Product Line	Wattstopper
Country Of Origin	China
Warranty Type	5-Year
UPC Number	754182922901

Dimensions

Product Depth US	1.7 in
Product Height US	2.2 in
Product Volume US	28.1 cu in
Product Width US	2.8 in
Product Weight US	0.3 lb

Additional Information

RoHS Compliant

Yes

This product meets the material restrictions of Article 4 of the RoHS Directive (2011/65/EU), including Commission Delegated Directive 2015/863.

Technical Information

Amperage	20 A
Connection Type	Wired

Resources

How do I tie in a SP switch into the BZ50? Will SP override the Bz50?

Asked by: Bob27

Please see attached diagram. If the switch is installed after the BZ as indicated, it does not override the BZ and attached sensors.

Answered by: Justin

Date published: 2024-12-10

I wired everything the way it says in the diagram but my motion sensor isn’t turning my lights off when I leave for 20min and the power back BZ-50 class 2 is flashing every 5 seconds seeing what the issue could be thanks.

Asked by: Jake

Please contact Wattstopper Technical Support @ 800-879-8585 for troubleshooting assistance.

Answered by: Justin

Date published: 2024-04-18

Can you use the Red 24VDC from 1 BZ-50 and connect to the blue input on another BZ-50 to control a load

Asked by: Luke

Hi Luke, No, you cannot hook up as described. Please follow the wiring diagram below to control more than one BZ-50 power pack from a single sensor.

Answered by: Tier 1 Tech Support

Date published: 2024-05-10

What is the Source/Sink limit in mA of the Blue Control Output wire?

Asked by: Paul Schmid

The transformer in the BZ-50 provides up to 225 mA of 24VDC power for the low voltage devices. The relay in the BZ-50 is switching and therefore does not have a Source/Sink mA limit. The relay will output either 120v or 277v depending on your input voltage.

Answered by: Justin

Date published: 2024-01-30

Trying to put these in an existing building, can I switch the power pack on and off with a switch in the room? Instead of the switch leg coming off the BZ-50? 

Asked by: Anonymous

Hello, The BZ-50 will allow a standard Line voltage switch to be installed on the Red switch leg wire.

Answered by: Justin

Date published: 2024-01-25

Can I use the BZ-50 to control 12watt Led wall lights? Max 3 fixtures, total 36w 120v

Asked by: Keith

Yes, as long as you do not exceed the 20A load limit.

Answered by: Tier 1 Tech Support

Date published: 2024-01-18

Is there a minimum load requirement for the BZ-50?

Asked by: Tristan

How much sensor can use this power pack

Answered by: Val

Date published: 2024-05-23

What is the recommended relay for the BZ-50?

Asked by: Aaron

Does the power pack needs a switch leg from the switch or can i use Switch leg from light for the sensor to work

Answered by: Keith

Date published: 2022-10-31

Power Pack, 120-277V, 50/60Hz, 24VDC, 225mA Questions - page 2

Power Pack, 120-277V, 50/60Hz, 24VDC, 225mA, Wire Connector

Features

Specifications

Resources

Cutsheet

Installation Instructions

CAD Drawings

Brochure

Specifications

White Papers & Tech Bulletins

Case Studies

Reviews

Questions & Answers

How do I tie in a SP switch into the BZ50? Will SP override the Bz50?

I wired everything the way it says in the diagram but my motion sensor isn’t turning my lights off when I leave for 20min and the power back BZ-50 class 2 is flashing every 5 seconds seeing what the issue could be thanks.

Can you use the Red 24VDC from 1 BZ-50 and connect to the blue input on another BZ-50 to control a load

What is the Source/Sink limit in mA of the Blue Control Output wire?

Trying to put these in an existing building, can I switch the power pack on and off with a switch in the room? Instead of the switch leg coming off the BZ-50?

Can I use the BZ-50 to control 12watt Led wall lights? Max 3 fixtures, total 36w 120v

Is there a minimum load requirement for the BZ-50?

What is the recommended relay for the BZ-50?

Power Pack, 120-277V, 50/60Hz, 24VDC, 225mA, Wire Connector

Features

Specifications

Resources

Cutsheet

Installation Instructions

CAD Drawings

Brochure

Specifications

White Papers & Tech Bulletins

Case Studies

Related Products

Reviews

Questions & Answers

How do I tie in a SP switch into the BZ50? Will SP override the Bz50?

I wired everything the way it says in the diagram but my motion sensor isn&rsquo;t turning my lights off when I leave for 20min and the power back BZ-50 class 2 is flashing every 5 seconds seeing what the issue could be thanks.

Can you use the Red 24VDC from 1 BZ-50 and connect to the blue input on another BZ-50 to control a load

What is the Source/Sink limit in mA of the Blue Control Output wire?

Trying to put these in an existing building, can I switch the power pack on and off with a switch in the room? Instead of the switch leg coming off the BZ-50?&nbsp;

Can I use the BZ-50 to control 12watt Led wall lights? Max 3 fixtures, total 36w 120v

Is there a minimum load requirement for the BZ-50?

What is the recommended relay for the BZ-50?

I wired everything the way it says in the diagram but my motion sensor isn’t turning my lights off when I leave for 20min and the power back BZ-50 class 2 is flashing every 5 seconds seeing what the issue could be thanks.

Trying to put these in an existing building, can I switch the power pack on and off with a switch in the room? Instead of the switch leg coming off the BZ-50?